EMC Directive: which products need EMC testing, and how

Marc HaddadForward Deployed Regulatory Engineer
If your product has electrical or electronic parts and is sold in the EU, assume the Electromagnetic Compatibility (EMC) Directive 2014/30/EU applies until you can show it doesn’t. The Directive requires that your product neither disturbs other equipment nor is disrupted by it. The manufacturer usually shows this through its own testing, then signs a declaration and affixes the CE marking.
Key points
- Two requirements: your product must limit the disturbance it emits and withstand normal disturbance from other equipment.
- Battery products: these are in scope, because the Directive has no voltage threshold. Products with a radio go under the Radio Equipment Directive instead.
- Conformity route: self-assessment is the norm, with most products using Module A, and a notified body is optional.
- Cited standards: test to the cited standard, because only editions cited in the Official Journal give presumption of conformity.
- Documentation: keep the technical file and declaration for 10 years, and reassess when the design changes.
What is the EMC Directive?
The EMC Directive, Directive 2014/30/EU, is the EU law on electromagnetic compatibility: a product’s ability to work in its electromagnetic environment without disturbing anything else in that environment.[1] In plain terms, it covers the electrical noise a product gives off and how well it copes with noise from everything else.
Emissions: this is the noise your product makes. A motor sparking at its brushes, a switch-mode power supply and a microcontroller clock all produce it, and it travels down cables or radiates into the air.
Immunity: this is the reverse, meaning a static shock from a user’s finger, a surge on the mains or a phone transmitting nearby should not make your product reset, lock up or misbehave. Together these are the Directive’s two essential requirements, the outcomes every product in scope must meet.[1]
Does the EMC Directive apply to my product?
It does if your product is “apparatus” or a “fixed installation” in the Directive’s terms and isn’t excluded.[1] Battery power doesn’t take a product out of scope, because the Directive has no voltage threshold.
- Apparatus: a finished appliance, or combination of appliances, made available as a single functional unit, intended for the end user and liable to generate disturbance or be affected by it. Components and sub-assemblies the end user builds in, such as a plug-in card or a replacement power supply, count too, as do mobile installations.[1]
- Fixed installation: an installation assembled for permanent use at one location, such as a production line or a building’s power distribution. It must follow good engineering practice and be documented, but needs no EU declaration of conformity and no CE marking.[1] Apparatus built for one specific installation and not sold elsewhere is relieved of most apparatus duties, though its documentation must still identify the installation and that installation’s EMC characteristics.[1]
The table shows how this works out for common product types, with the standards usually cited and the other EU laws that apply alongside (Module A is the self-assessment route explained below).
| Product | EMC Directive? | Typical cited standards | Other acts, and the route |
|---|---|---|---|
| Battery toy with a motor and sound chip | Yes | EN 55014-1, EN 55014-2 | Toy safety law; self-assessment (Module A) |
| Mains kitchen appliance | Yes | EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 | Low Voltage Directive (LVD); Module A |
| Hand-held power tool | Yes | Same as the kitchen appliance | Machinery law; Module A |
| Boxed 24 V DC industrial controller | Yes | EN 61000-6-2, EN 61000-6-4 | Often installed in machinery; Module A |
| Mains LED luminaire | Yes | EN IEC 55015, EN 61547, EN 61000-3-2, EN 61000-3-3 | LVD; Module A |
| Product with Bluetooth | No: RED applies and covers EMC (RED Article 3(1)(b)) | EMC is still tested, under RED | RED route |
| Passive item with no electronics | No | None | Other acts may still apply |
Three categories need more than a yes or no:
- Mains electrical products: a product rated between 50 and 1,000 V AC (alternating current) or between 75 and 1,500 V DC (direct current) also falls under the Low Voltage Directive, Directive 2014/35/EU, for electrical safety.[2] Battery products below that band are outside the LVD but still within the EMC Directive.
- Toys: toy safety rules apply alongside EMC rather than replacing it. The Toy Safety Directive 2009/48/EC is repealed with effect from August 1, 2030, and from that date Regulation (EU) 2025/2509 applies.[3]
- Machinery: machinery law has its own immunity requirement, under which external radiation must not interfere with the machine’s operation.[4] That requirement is about safety, for example a guard interlock that must ignore a nearby transmitter, while the EMC Directive covers emissions and normal performance. Both apply, and one declaration covers both.
Which products are excluded from the EMC Directive?
The exclusions are narrow. A product with Bluetooth or another radio falls under the Radio Equipment Directive (RED), Directive 2014/53/EU, which covers EMC itself. Adding a radio module makes the whole product radio equipment.
The Directive also excludes:[1]
- Aviation products: aeronautical products, parts and appliances covered by EU aviation safety rules
- Radio amateur equipment: radio amateur equipment that is not made available on the market
- Electromagnetically benign equipment: equipment that, because of its physical nature, cannot emit disturbing levels and is not degraded by normal disturbance
- Evaluation kits: custom-built evaluation kits used by professionals only at research and development facilities.
The Directive also steps aside where more specific EU law covers EMC.[1] The Medical Device Regulation (MDR), Regulation (EU) 2017/745, declares itself to be that law, so a medical device meets its EMC requirements through the MDR.[5] A wellness gadget that is not a medical device stays under the EMC Directive. Vehicles and their electronic sub-assemblies are approved to UN Regulation No 10 through vehicle type approval.[6]
Who is responsible for EMC compliance?
The manufacturer is responsible, meaning whoever makes the apparatus, or has it designed or made, and markets it under their own name or trade mark.[1] Importers check that the manufacturer has done its part and add their own contact details,[1] and distributors check the CE marking and the accompanying documents.[1]
An importer or distributor that sells under its own brand, or modifies apparatus in a way that may affect compliance, becomes the manufacturer.[1] The manufacturer, importer and distributor obligations differ across EU product law.
How do you show conformity with the EMC Directive?
Most products take the self-assessment route, and a notified body is optional. The Directive gives two routes:[1]
- Internal production control, Module A: you assess EMC across all normal operating conditions and each representative configuration, compile technical documentation that includes your test reports, and declare conformity yourself.[1]
- EU-type examination followed by conformity to type, Modules B and C: a notified body examines your technical documentation, without testing a specimen, and issues a certificate.[1, 7] You can limit this to some aspects of the essential requirements. It mainly helps where you haven’t applied harmonised standards, or applied them only in part, and want an independent opinion on your own assessment.
Two points cause confusion. First, an EMC test lab is not a notified body, since notified bodies are designated by Member States and listed in NANDO, the Commission’s database. Second, the test report is not compliance in itself: the legal duty is to meet Annex I, and the report is your evidence that you do.
Which standards apply for EMC testing?
Use the product-family standard for your product, and fall back to the generic standard for your environment only if no product-family standard fits. Harmonised standards are voluntary, but those whose references are published in the Official Journal of the EU give a presumption of conformity: meet them and you are presumed to meet the requirements they cover.[1]
For EMC, the cited references sit in two places: the Commission communication in OJ C 246 of July 13, 2018, and Implementing Decision (EU) 2019/1326, last amended by Implementing Decision (EU) 2022/910. The table lists the main cited references by product family.
| Product family or environment | Cited references |
|---|---|
| Household appliances, electric tools and toys | EN 55014-1:2017/A11:2020 (emissions); EN 55014-2:1997 with A1 and A2 (immunity) |
| Multimedia and IT equipment | EN 55032:2015/A11:2020 (emissions); EN 55035:2017/A11:2020 (immunity) |
| Lighting | EN IEC 55015:2019/A11:2020 (emissions); EN 61547:2009 (immunity) |
| Industrial, scientific and medical radio-frequency equipment | EN 55011:2016 with A1 and A11 |
| Measurement, control and laboratory equipment | EN 61326-1:2013 |
| Generic, residential environment | EN 61000-6-3:2007/A1:2011 (emissions); EN 61000-6-1:2007 (immunity) |
| Generic, industrial environment | EN 61000-6-4:2007/A1:2011 (emissions); EN 61000-6-2:2005 (immunity) |
| Mains-connected products | EN 61000-3-2:2014 (harmonic currents); EN 61000-3-3:2013 (voltage fluctuations and flicker) |
Several cited editions are older than the latest ones the standards bodies have published, and only the cited reference gives presumption of conformity. If your lab tested to a newer edition that is not cited, your own assessment has to show that it covers the essential requirements. References are added and withdrawn by Commission decision, often with a transition period, so the editions in your technical file can go stale without notice. Daptic tracks regulatory changes like these and flags the ones that affect your products, along with which requirements apply to each product in each market you sell into.
What happens during EMC testing for CE marking?
The lab measures what your product emits and checks how it behaves under disturbance, at test levels and performance criteria set by the product-family or generic standard. The performance criteria define how much degradation is acceptable during and after each test.
Emissions tests measure conducted noise on mains and other cable ports, radiated noise in a shielded chamber or on an open-area test site, and, for mains products, harmonic currents and flicker. Immunity tests, which come from the EN 61000-4 basic standards, apply electrostatic discharge, radiated radio frequency, fast transient bursts, surges and conducted radio frequency, plus voltage dips and interruptions for mains products.
To prepare a unit for the lab:
- Representative build: send a production-representative unit with the final enclosure, cables, power supply and firmware.
- Worst-case mode: run it in its worst-case mode, for example the motor at full load, every port cabled and the display on.
- Pass criteria: write down beforehand what “working normally” means, because that is how immunity results are judged.
- Support kit: bring the support equipment, a list of configurations and a rework kit of ferrites and capacitors.
What paperwork does the EMC Directive require?
You need five things, and they have to stay current:
- Technical documentation: a product description, design and manufacturing drawings, your EMC assessment, the standards you applied and your test reports.[1] Keep it with the declaration for 10 years after the apparatus is placed on the market.[1] Importers keep a copy of the declaration for the same period.[1]
- EU declaration of conformity: one declaration that names every act that applies.[1]
- CE marking: this must be affixed visibly, legibly and indelibly before the product is placed on the market.[1]
- Identification: a type, batch or serial number, plus your name, trade mark and postal address.[1]
- Instructions: these must be in a language users understand,[1] including any precautions for assembly, installation or use, and a clear notice if the product is not meant for residential areas.[1] Equipment tested only to industrial “Class A” limits falls into that last case.
Conformity doesn’t end at launch, because series production must stay in conformity as the design and the cited standards change.[1] You must also take corrective action if a product does not conform.[1] Treat a board revision as an EMC event, because a new power supply, layout or clock change can invalidate old results.
Example: applying the EMC Directive to a food processor
Here is how a manufacturer would work through the steps above for a mains-powered food processor, in an example that is a composite of several cases. The processor has a brushed universal motor, a control board with a microcontroller and a capacitive touch panel, a switch-mode supply for the electronics, and no radio.
- Scope: it is apparatus, because the motor and supply emit noise and the touch panel can be disturbed. As a household appliance it falls under the LVD for electrical safety, not machinery law.[4]
- Standards: EN 55014-1 and EN 55014-2, plus EN 61000-3-2 and EN 61000-3-3, because the motor draws a sharp current step at start-up.
- Lab: conducted emissions fail first, driven by the motor brushes, and a suppression capacitor and a ferrite fix that. In the static discharge test, touching the panel resets the board and the user has to restart the machine. The team checks this against the standard’s performance criterion and fixes the firmware.
- File: the suppression parts are marked EMC-critical on the parts list, and the declaration names Directive 2014/30/EU, Directive 2014/35/EU and every other act that applies.
- Eight months later: purchasing swaps in a cheaper power supply. That counts as a design change,[1] so the team reassesses, repeats at least the conducted emissions test and updates the file before the new build ships.
What is changing in the EMC Directive?
One amendment already applies, a proposal on digital paperwork is still going through the EU process, and the machinery law that sits alongside EMC changes in January 2027.
- Directive (EU) 2024/2749: since May 30, 2026, the emergency procedures this amendment added to the EMC Directive have applied.[1] They take effect only if the EU activates an internal market emergency mode.
- Digitalisation omnibus, COM(2025) 503: the proposal would require an electronic declaration of conformity and a digital contact on the product, and would allow electronic instructions, with paper free on request.[8] On June 26, 2026, Coreper, the Council committee of Member State representatives, confirmed the negotiated text, and on July 14, 2026, the Parliament committee approved it. The plenary vote is indicatively set for November 23, 2026, and the proposal is not adopted.
- Machinery Regulation (EU) 2023/1230: from January 20, 2027, this regulation applies and replaces the Machinery Directive in every machinery declaration.
Frequently asked questions
Does the EMC Directive apply to battery-powered products?
Yes, battery products are in scope even when they fall below the Low Voltage Directive’s range, because the EMC Directive has no voltage threshold.
Do I need a notified body for EMC Directive compliance?
No, self-assessment under Module A is enough for almost every product, and the notified body route in Annex III is optional.[1]
Do I still need EMC testing if I use a CE-marked power supply?
Yes, because the finished product is the apparatus you declare, and a compliant power supply inside a non-compliant enclosure still fails.
Does an FCC test report cover EMC for CE marking?
No, FCC (US Federal Communications Commission) authorisation is a separate US regime. You can reuse its lab data only where you show it meets the EU’s cited methods and limits.
Does the EMC Directive apply to products with Bluetooth?
No, a product with a radio falls under the Radio Equipment Directive, which covers EMC itself, so EMC is still tested, but under RED.[9]
How long do I keep EMC technical documentation?
Keep it, with the EU declaration of conformity, for 10 years after the apparatus is placed on the market.[1]
Notes and sources
- Directive 2014/30/EU (EMC), consolidated version of May 30, 2026, particularly Articles 2, 3, 7, 9–11, 13, 14, 17, 18 and 19(1); Article 6 and Annex I; Article 19 and Annex I, point 2; Annex II (Module A); Annex III (Modules B and C); Annex II, point 3; Article 15 and Annex IV; Articles 40a to 40c, added by Directive (EU) 2024/2749.
- Directive 2014/35/EU (LVD), particularly Article 1.
- Regulation (EU) 2025/2509 (toys), particularly Articles 56 and 59.
- Directive 2006/42/EC (Machinery), particularly Article 1(2)(k); Annex I, 1.5.11.
- Regulation (EU) 2017/745 (MDR), particularly Article 1(11).
- Regulation (EU) 2019/2144, particularly Annex I.
- examination of the technical documentation without a specimen is Annex III, Part A, point 2.
- COM(2025) 503 and procedure 2025/0133(COD)), particularly Article 5.
- Directive 2014/53/EU (RED), particularly Article 3(1)(b).
Additional sources:
- Last reviewed: November 9, 2026.
- Commission communication, OJ C 246, July 13, 2018 (EMC harmonised standards)
- Implementing Decision (EU) 2019/1326, consolidated version of June 10, 2022
- Directive (EU) 2024/2749
- European Commission, EMC harmonised standards
- European Commission, EMC Directive page
This article reflects Marc Haddad’s independent opinions, not necessarily those of Daptic.



