Daptic announces $22M funding to bring compliance into product development. Learn More
Request Demo
Expert Authored

Harmonised standards explained: are standards mandatory, and what is presumption of conformity?

Harmonised standards are voluntary in the EU. Learn what presumption of conformity gives you, where the Official Journal list is, and how to cite them.
A blue card titled Harmonised Standards Citations listing four dated Official Journal changes, with 20 January 2027 marked as the deadline.
November 10, 2026

Marc HaddadMarc HaddadForward Deployed Regulatory Engineer

 

Under European Union (EU) product law, harmonised standards are never mandatory, but the law’s essential requirements are. If you apply a harmonised standard whose reference is published in the Official Journal of the European Union under the act you declare against, you get presumption of conformity for the requirements it covers. That makes it the cheapest way to prove you meet them.

Key points

 

  • Voluntary, not mandatory: harmonised standards are voluntary, so you may meet the law’s essential requirements another way, but then you build the evidence yourself.
  • Where presumption comes from: only a harmonised standard cited in the Official Journal under the act you declare against gives presumption of conformity. It covers only the requirements that standard addresses and the clauses you applied.
  • The legal list: the Commission implementing decision for each act is the legal list of cited standards, while the summary list on the Commission’s website has no legal effect of its own.
  • One requirement at a time: work through your product requirement by requirement, covering each one either with a cited clause you applied or with evidence you build yourself.

What are harmonised standards?

 

Harmonised standards (“harmonized” in US spelling) are European standards written at the European Commission’s request so that manufacturers can show their products meet EU product law. The law sets the outcome you have to reach, for example that an appliance must not give an electric shock, but it rarely says how. Standards fill that gap with test methods, limits and design rules.

 

Regulation (EU) No 1025/2012 on European standardisation defines the terms:

 

  • European standard (EN): a standard adopted by a European standardisation organisation, which is CEN (European Committee for Standardization), CENELEC (European Committee for Electrotechnical Standardization) or ETSI (European Telecommunications Standards Institute).[1]
  • Harmonised standard: a European standard adopted at the Commission’s request for applying EU product legislation.[1]

 

Once the Commission finds that a harmonised standard meets the requirements it aims to cover, it publishes the standard’s reference in the Official Journal.[1] That publication is what gives the standard legal effect, and the Court of Justice of the European Union has held that a harmonised standard whose reference has been published “forms part of EU law”.[2]

Are harmonised standards mandatory?

 

No. Regulation 1025/2012 defines a standard as one “with which compliance is not compulsory”.[1] What the law makes mandatory is its essential requirements, the outcomes your product must reach.

 

You can legally choose not to apply a harmonised standard, but then you “must demonstrate that the products are in conformity with essential requirements” another way, according to the Blue Guide, the Commission’s guidance on EU product rules.[3] In practice that means writing the full justification for every requirement yourself. For some machinery you also lose the option of assessing the product yourself (see the section on conformity assessment below).

What is presumption of conformity?

 

Presumption of conformity means that a product built to a cited harmonised standard is presumed to meet the essential requirements that standard covers, so the standard becomes your evidence for those requirements.

 

Every product act has a presumption clause. Under the Low Voltage Directive 2014/35/EU (LVD), electrical equipment that conforms to “harmonised standards or parts thereof” whose references are published in the Official Journal is presumed to meet the safety objectives those standards cover.[4] The Electromagnetic Compatibility (EMC) Directive 2014/30/EU says the same about its essential requirements,[5] and the Machinery Regulation (EU) 2023/1230 does it for the essential health and safety requirements in its Annex III.[6] The wording changes from act to act, but the mechanism is the same.

 

Presumption has limits:

 

  • Covered requirements only: presumption reaches only the requirements the standard is written to cover, which are usually listed in an informative annex to the standard.[3] It applies “only to the extent” that the standard corresponds to those requirements.[3]
  • European version only: only the European version of a standard gives presumption, not the ISO (International Organization for Standardization) or IEC (International Electrotechnical Commission) original it was based on.[3]
  • Market surveillance still applies: presumption does not exempt your product from market surveillance, the checks national authorities make on products already on the market. The LVD’s procedure for products presenting a risk expressly allows for shortcomings in a cited standard.[4]

 

The table below shows what each type of evidence gets you and what your technical file (the documentation that proves conformity) has to contain.

 

Evidence you use Status Presumption of conformity What your technical file must hold
Harmonised standard, reference published under the act you declare against Voluntary Yes, for the requirements it covers and the clauses you applied Reference and edition, clauses applied, test reports
Other standard: an EN not cited under that act, an ISO or IEC text, a national standard Voluntary No The standard as supporting evidence, plus your own reasoning on how each requirement is met
No standard Not applicable No Your own risk assessment, design solutions and test evidence, requirement by requirement

What do manufacturers have to do?

 

Go through your product one essential requirement at a time and record what covers each one.

 

  1. Your acts: list the EU acts you declare against, which for a mains-powered appliance could be the LVD and the EMC Directive.
  2. Cited standards: find the standards cited under each act in the Commission implementing decision that lists them (see the next section).
  3. Coverage for each requirement: note the cited clause you applied, and where no cited clause covers a requirement, build your own risk assessment, design solutions and test evidence.
  4. Editions: check each edition you cite for restrictions and for the date its presumption ends.

 

Then write it up. Under the LVD, the technical documentation lists the harmonised standards “applied in full or in part” and, for any standard applied only in part, says which parts. Where you did not apply them, it describes the solutions you adopted instead.[4]

 

The declaration of conformity, the document in which you declare that the product meets the act, gives the references of the harmonised standards used,[4] each with its version or date.[3] Listing a standard there does not prove you meet it, because presumption comes from conformity with the standard, not from the listing.[4]

Where is the harmonised standards list in the Official Journal?

 

The legal list for each act is the Commission implementing decision published in the Official Journal. The Commission’s harmonised standards page for each act also has a summary list, but that list is for information only and “does not as such generate legal effects”.

 

Since December 1, 2018, references have been published and withdrawn through implementing decisions, and these are the ones to check:

 

  • LVD: Implementing Decision (EU) 2023/2723 of December 6, 2023, amended four times since, most recently by Implementing Decision (EU) 2025/1488 of July 22, 2025.
  • EMC Directive: Implementing Decision (EU) 2019/1326 of August 5, 2019, last amended on June 9, 2022, by Implementing Decision (EU) 2022/910, read together with the Commission communication in Official Journal C 246 of July 13, 2018.
  • Machinery Regulation: no list yet (see the next section).

 

New decisions add, replace, restrict or withdraw references, often several times a year for each act. Keeping each product’s declared editions in line with them is the kind of job Daptic does by tracking these implementing decisions and flagging the changes that affect the standards your products declare against, rather than relying on someone re-reading the Commission pages.

What happens when a harmonised standard is revised, restricted or withdrawn?

 

Presumption can end or shrink when a standard is revised, restricted or withdrawn.

 

  • Superseded (replaced) editions: when a revised edition is cited, its Official Journal reference gives the date when presumption from the old edition ends.[3] Until that date both editions count, and after it a declaration that still cites the old edition gets no presumption from it. Products made to the old edition may still conform, but you have to show that the gap between the two editions is closed.
  • Objections and restrictions: a Member State or the European Parliament can formally object to a standard, and the Commission then decides whether to publish the reference, not publish it or publish it “with restriction”. For a reference already published, it decides whether to keep it, keep it with a restriction or withdraw it.[1] A restriction can remove presumption for named clauses while the rest of the standard still counts.
  • Cited under one act, not another: a citation works only under the act that lists it, so citations under the Machinery Directive will lose their legal effect on January 20, 2027, when Regulation (EU) 2023/1230 applies. When this article was last reviewed, the Commission’s machinery page said the first list under the Regulation was being prepared and was expected before the end of 2026. Until it is published, no standard gives presumption under the Regulation.

What if there is no harmonised standard for a requirement?

 

You build the evidence yourself: your own risk assessment, design solutions and test evidence. Some acts let the Commission adopt common specifications as a fallback, which are technical specifications the Commission sets itself by implementing act.

 

The Machinery Regulation allows common specifications only in narrow cases, where a standardisation request was not accepted or the resulting standard was not delivered within the deadline or did not comply with the request. The Regulation also requires that no suitable reference can be expected within a reasonable period.[6]

Do harmonised standards affect the conformity assessment route?

 

Yes, under some acts. Conformity assessment is the procedure for showing that a product meets the act, and under some acts, whether you may assess the product yourself depends on harmonised standards.

 

  • LVD: there is one route, internal production control (you assess the product yourself), with no notified body.[4]
  • EMC Directive: you choose between internal production control and EU-type examination by a notified body, which is an outside assessment body.[5]
  • Machinery Regulation: machinery listed in Annex I Part B may use internal production control (module A) only if it is designed and built in accordance with harmonised standards or common specifications. Otherwise one of the third-party procedures applies.[6]

 

Our article on notified bodies covers how to choose one.

Do you have to pay for harmonised standards?

 

Yes, for now. National standardisation bodies republish each European standard as a national standard,[3] and you buy it from them. Regulation 1025/2012 only asks them to encourage and facilitate access for small firms, for example by putting abstracts online free of charge and offering special rates or reduced-price bundles.[1]

 

On October 6, 2026, the Commission proposed a new Regulation on European standardisation, COM(2026) 780, procedure 2026/0307(COD), which may change that. It would repeal Regulation 1025/2012,[7] and it would also require free online access to referenced standards, including after their references are withdrawn.[7] It would apply six months after entering into force.[7]

 

The proposal now goes to the Parliament and the Council, and until a new regulation is adopted and applies, Regulation 1025/2012 governs and you keep buying the standards you apply.

Example: applying this to a countertop blender

 

Here is a composite example of the steps above: a maker of a mains-powered countertop blender declares against the LVD and the EMC Directive. For electrical safety it applies the general household appliance standard, EN 60335-1, which is cited under the LVD.[8] For EMC it applies the emission and immunity standards cited for household appliances.

 

The team assumed that the part 2 standard for kitchen machines, EN 60335-2-14:2006, covered the blades, but it doesn’t. Germany formally objected that the standard did not keep blades out of reach during operation and that its test probe was not based on body dimensions. Implementing Decision (EU) 2025/1464 of July 17, 2025, then decided not to publish the reference.[9] It found that the standard fails safety objectives 1(c), 2(a), 2(c) and 3(b) of Annex I to the LVD,[9] so although it is an EN, it gives no presumption under the LVD.

 

For blade access, the maker wrote its own case: a hazard analysis, the guard and interlock design, and a test probe it could justify. It recorded these in its technical documentation as the solutions it adopted instead.[4] The declaration names the EN 60335-1 edition and the EMC standards, and does not present EN 60335-2-14 as a harmonised standard. Run the same check on every standard your own technical file relies on.

Frequently asked questions

Are harmonised standards mandatory in the EU?

No. Harmonised standards are voluntary, and what EU product law makes mandatory is its essential requirements. If you don’t apply a cited harmonised standard, you must show conformity with those requirements another way.

What is presumption of conformity?

Presumption of conformity means a product that conforms to a harmonised standard cited in the Official Journal is presumed to meet the essential requirements that standard covers. It applies only under the act that cites the standard and only to the clauses you applied.

Does every EN standard give presumption of conformity?

No. Only the cited edition of a harmonised standard gives presumption, only under the act that cites it, and only within any restriction. EN 60335-2-14:2006, for example, is an EN but gives no presumption under the Low Voltage Directive.

Where is the official list of harmonised standards?

The official list is the Commission implementing decision for each act, published in the Official Journal, while the summary lists on the Commission’s harmonised standards pages are for information only.

Notes and sources

 

  1. Regulation (EU) No 1025/2012 on European standardisation, Articles 2, 6, 10, 11
  2. CJEU, Case C-613/14, James Elliott Construction, October 27, 2016, particularly paragraph 40.
  3. Blue Guide 2022, Commission Notice 2022/C 247/01), sections 4.1.2, 4.1.3, 4.4
  4. Directive 2014/35/EU (Low Voltage), Articles 6, 12 to 14, 19; Annexes III and IV
  5. Directive 2014/30/EU (EMC), Articles 13 and 14
  6. Regulation (EU) 2023/1230 (Machinery), Articles 20 and 25
  7. Proposal for a Regulation on European standardisation, COM(2026) 780, particularly Articles 5, 42 and 43.
  8. Commission Implementing Decision (EU) 2023/2723 (LVD standards), particularly Annex I, row 155, with its amendments.
  9. Commission Implementing Decision (EU) 2025/1464 (EN 60335-2-14:2006), particularly Article 1; recital 8.

 

Additional sources:

 

 

This article reflects Marc Haddad’s independent opinions, not necessarily those of Daptic.

Resources

Related Articles

Request a Demo Today