IMDS reporting and the End-of-Life Vehicles rules: what automotive suppliers have to declare

Marc HaddadForward Deployed Regulatory Engineer
IMDS, the International Material Data System, is the automotive industry’s shared database where suppliers declare the materials and substances in each part they sell into a vehicle. No law names it. Carmakers require it by contract to show compliance with the End-of-Life Vehicles Directive, REACH and their own substance lists.
Key points
- IMDS is an industry system that carmakers require by contract. The End-of-Life Vehicles (ELV) Directive bans four heavy metals in vehicle parts but never mentions IMDS or any data format.
- The declaration goes well beyond the four metals. It covers every material and substance in the part, and substances on industry lists and the REACH Candidate List have to be named.
- A part can pass the legal test and still fail the declaration, and an accepted declaration doesn’t prove the part is legal.
- Regulation (EU) 2026/1738 replaces the ELV Directive from September 1, 2028, and its recycled-content duties will run through the same supply chain.
What is IMDS?
IMDS is a web database in which each supplier in a vehicle’s supply chain records what its parts are made of, so the carmaker can add the data up for the whole vehicle. It began as a joint project of Audi, BMW, Daimler, Ford, Opel, Porsche, VW, Volvo and the IT firm EDS, which is now part of DXC Technology.
The manufacturers still steer it. In November 2026 the IMDS public pages listed 42 car, truck, engine and motorcycle makers on its steering committee. That committee writes the IMDS Recommendations, which set the data rules, and IMDS notes that many companies treat them as requirements. Suppliers use the browser version free, because the carmakers pay for the system. Uploading in bulk from your own software needs a paid license.
Does the End-of-Life Vehicles Directive require IMDS?
No. The End-of-Life Vehicles Directive, Directive 2000/53/EC, sets the legal rules for cars and vans, and IMDS is how carmakers collect the evidence that they meet them.
Three parts of the Directive drive the data request. The first is a ban. Materials and components of vehicles put on the market after July 1, 2003 must not contain lead, mercury, cadmium or hexavalent chromium, except for the uses listed in Annex II, the exemptions list. Annex II tolerates up to 0.1% by weight per homogeneous material for lead, mercury and hexavalent chromium, and 0.01% for cadmium.[1] A homogeneous material is one that can’t be mechanically separated into other materials, such as a plating layer, a solder or a plastic resin.
The second is a set of targets. Since January 1, 2015, Member States have had to ensure that economic operators reach at least 95% reuse and recovery, and 85% reuse and recycling, by average vehicle weight.[1] The third is information. Vehicle producers must use coding standards for components and materials together with their material and equipment suppliers, and component makers must give treatment facilities dismantling information on request.[1, 2]
None of that can be shown without knowing what is in every part, and the carmaker buys most of its parts. So it pushes the question down the chain through purchase contracts, using IMDS as the format.
Suppliers often miss that the ban is written about materials and components, not only about finished vehicles. Through each Member State’s national law, it applies to your part whether or not anyone has asked you for a data sheet. The wider set of chemical rules that reach finished products is covered in our guide to restricted substances in products.
What does a supplier enter in IMDS?
A supplier enters a material data sheet (MDS) for each part. It is built as a tree: the component, any semi-components, the materials, and the basic substances in each material, with weights or percentages at each level.
Substances come from the IMDS basic substance list. You can attach data sheets your own suppliers have built instead of retyping them. A restricted metal used under an exemption, such as lead in brass, carries an application code that points to the Annex II entry it relies on.
You then send the sheet to your customer’s IMDS company ID, and the customer accepts or rejects it. An accepted sheet becomes part of the customer’s sheet for its assembly, and so on up each tier to the carmaker. IMDS Recommendation 001 sets the basic rules for declaring substances, and its latest revision took effect on April 24, 2026.
Which substances have to be declared in IMDS?
Every substance in the part is declared, but some have to be named and can never be hidden. Those come from lists that carry very different legal weight. The table shows where each list comes from and what it means for a data sheet.
| List | Who sets it | Legal force | What it means for your data sheet |
|---|---|---|---|
| ELV Annex II metals: lead, mercury, cadmium, hexavalent chromium | EU law, Directive 2000/53/EC | Ban, with listed exemptions | Named; any use above the limits carries an application code for its exemption |
| Global Automotive Declarable Substance List (GADSL) | Global Automotive Stakeholders Group: carmakers, suppliers, chemical and plastics industries | None in itself | Named; never marked confidential or hidden in a wildcard |
| REACH Candidate List of substances of very high concern | European Chemicals Agency | Information duty above 0.1% w/w of an article | Flagged in IMDS so your customer can meet its own duty |
| Carmaker lists, such as Renault’s | Individual carmakers | Contract only | Same handling as GADSL substances for that carmaker |
The GADSL covers substances expected to remain in the vehicle at the point of sale. Its maintainers ask users not to call it a ban list, because many of the listed substances are legal. REACH, the EU chemicals regulation, requires anyone supplying an article that contains a Candidate List substance above 0.1% by weight to pass on enough information for safe use, including at least the substance name.[3] REACH’s wider duties for articles and the PFAS rules have their own guides.
Two IMDS terms matter here. A wildcard is a placeholder for undisclosed minor ingredients, and a confidential substance is named but hidden from the customer. Neither may hold a GADSL substance.
This is where the declaration and the law part ways. Lead in brass within its Annex II exemption is legal, but you still declare it. A GADSL plasticizer that no law restricts in your use still goes on the sheet by name. An accepted sheet proves nothing if the exemption it cites has expired.
The lists also change. The Candidate List is updated about twice a year and the GADSL follows; IMDS put GADSL updates into effect on March 20 and September 11, 2026. The Commission amends Annex II by delegated directive, as it did in 2023 for lead in aluminum alloys, copper alloys and certain batteries.[4] After each GADSL update, Recommendation 001 requires suppliers to check every active data sheet for the new substances and re-send any sheet that hid one. Running that check across hundreds of part numbers is the hard part. Daptic tracks regulatory changes across jurisdictions and flags the ones that affect your products, so a new Candidate List entry or an expiring exemption gets traced to the parts it touches.
Do non-automotive suppliers have to report in IMDS?
Yes, in practice. Once an automotive customer sends you an IMDS request, you report, whatever you make. The duty comes from the customer’s purchase terms, not from the ELV Directive, and the customer can’t finish its own sheet without yours.
- Register: set up your company in IMDS, which gives you a company ID.
- Get the details: ask the customer for its company ID, part numbers and drawing weights, and read the supplier information its carmaker publishes in IMDS.
- Collect upstream data: ask your own suppliers for their IMDS sheets or full material declarations.
- Build, check and send: create the sheet, run the system checks and send it to the customer’s ID.
A supplier three or four tiers down sees only what its own suppliers disclose. A steel mill may have a published sheet you can attach. A coating distributor may send only a safety data sheet, which lists hazardous ingredients rather than the full composition. Closing that gap is your job, because IMDS makes both the creator and the receiver of a sheet responsible for its quality.
What makes the data hard depends on the product:
- Electrical and electronic parts, radio modules included: solders, terminations, glass and ceramics hold most of the lead exemptions. Component data from electronics suppliers often has to be mapped into IMDS.
- Machined, plated and coated metal parts: free-cutting steels and brass may contain exempt lead, and passivation coatings have to be confirmed free of hexavalent chromium. Each coating layer counts as its own material.
- Plastic and rubber parts: fillers, flame retardants, plasticizers and pigments are where GADSL and Candidate List substances usually turn up.
- Greases, adhesives and paints: a mixture that stays in the vehicle is declared as a material, and its maker may keep only ingredients that aren’t on the GADSL confidential.
Why do IMDS submissions get rejected?
Most rejections come from a few avoidable errors. The supplier that created the sheet fixes them, even when the cause sits in an upstream sheet it attached. These are the ones I see most often:
- Weights: the declared weight doesn’t match the drawing or the part, or the materials don’t add up.
- Hidden substances: a GADSL or Candidate List substance is put in a wildcard or marked confidential.
- Exemptions: a restricted metal has no application code, or the code cites an expired exemption.
- Structure: a plating isn’t entered as its own material, or a grease is entered as a component.
- Customer rules: each carmaker publishes its own requirements, so a sheet one customer accepts can fail with another.
IMDS’s automatic checks only show where to look. They aren’t a pass mark, and IMDS says they shouldn’t be used to reject data without someone reviewing it. When an upstream sheet is wrong, your supplier fixes it, you update the reference and you re-send.
How are the End-of-Life Vehicles rules changing?
A regulation is replacing the Directive, but most of it doesn’t apply yet. Regulation (EU) 2026/1738 covers circularity requirements for vehicle design and the management of end-of-life vehicles. It was adopted on July 8, 2026, published in the Official Journal on July 24, 2026, and entered into force on August 13, 2026. It applies from September 1, 2028. Until then, the ELV Directive still applies. Its four-metal ban and Annex II exemptions carry on until August 31, 2032, except Annex II entries 5(a), 5(b)(i), 5(b)(ii) and 16, which stopped applying on August 13, 2026. Directive 2005/64/EC, the type-approval rules on reusability, recyclability and recoverability, stays in force until August 31, 2032.[5]
According to the Commission, the Regulation:
- extends the rules over time to trucks, buses and motorcycles
- requires recycled plastic in vehicle types type-approved from 2032 at 15%, rising to 25% from 2036, with recycled steel and aluminum targets still to be set and expected from 2033[5]
- adds circularity passports for vehicles and makes producers pay for collection and treatment.
For suppliers, the change is in what the data has to carry. Recycled content is measured against the whole vehicle, but the recycled resin sits in a part molded two or three tiers down. Carmakers will need the recycled share of each material, with evidence, from the same chain that fills IMDS today.
The Commission’s summaries don’t mention IMDS, and by November 2026 IMDS had announced no changes for the Regulation. Before September 1, 2032, check every application code you rely on against the Regulation’s own substance rules in Annex IV, and check now any code that cites Annex II entries 5(a), 5(b)(i), 5(b)(ii) or 16.[5] Don’t assume Annex II carries over unchanged.
Example: a fastener maker’s first IMDS request
Here is how this works for one product, in a composite case. A maker of plated steel fasteners sells mostly to equipment makers. Then a seat-frame supplier sends it an IMDS request for three screws going into a new car program.
It registers and builds one sheet per part number. Each screw has three materials: the steel, a zinc-nickel plating, and a trivalent passivation coating with a sealer. The steel mill has a published sheet, so the maker attaches it instead of retyping the steel. The plating chemistry supplier sends only safety data sheets, so the maker asks for the full composition of the deposited layers. It also gets written confirmation that the passivation contains no hexavalent chromium.
One screw is cut from leaded free-cutting steel. That lead is legal under an Annex II exemption, so it is declared by name with that exemption’s application code.
The first submission is rejected for two reasons: the declared weight is 4% under the drawing, and the sealer went in as a wildcard. The maker weighs production parts, rebuilds the sealer from named substances, checks them against the GADSL and re-sends, and the second sheet is accepted. From then on, it reviews each sheet after every GADSL and Candidate List update.
Frequently asked questions
Is IMDS required by law?
No. The ELV Directive bans lead, mercury, cadmium and hexavalent chromium in vehicle materials and components but prescribes no data format. Carmakers require IMDS through their purchase contracts.
Is IMDS free for suppliers?
Yes, through the browser, because the carmakers pay for the system. Only bulk upload from your own software needs a paid license.
What substances have to be declared in IMDS?
All of them. The ELV metals, GADSL substances, REACH Candidate List substances and substances on carmakers’ own lists have to be named, never hidden in a wildcard or marked confidential.
Is the GADSL a list of banned substances?
No. It lists substances that must be declared because they are or may be regulated, and its maintainers say many of them are legal.
When does the new ELV Regulation replace the Directive?
Regulation (EU) 2026/1738 applies from September 1, 2028, when the Directive is repealed. The Directive’s four-metal ban and Annex II exemptions stay the legal test until August 31, 2032, apart from four entries that stopped applying on August 13, 2026.
Notes and sources
- Directive 2000/53/EC (ELV Directive), particularly Articles 7(2) and 8; Article 4(2)(a) and Annex II.
- Commission Decision 2003/138/EC
- Regulation (EC) No 1907/2006 (REACH), particularly Article 33(1).
- Commission Delegated Directive (EU) 2023/544
- Regulation (EU) 2026/1738 (ELV Regulation), particularly Articles 5, 6, 57 and 59.
Additional sources:
- Directive 2005/64/EC
- European Commission, End-of-life vehicles
- European Commission, “New rules for a more circular European automotive sector,” August 12, 2026
- European Chemicals Agency, Candidate List
- IMDS public pages
- IMDS, Reading for new users
- IMDS, Members of the IMDS Steering Committee
- IMDS, REACH SVHC
- IMDS FAQ, Legislative requirements
- IMDS FAQ, System usage
- IMDS News
- Global Automotive Declarable Substance List (GADSL)
This article reflects Marc Haddad’s independent opinions, not necessarily those of Daptic.



