Conformity of production: what authorities check after type approval

Michelle NgSenior Regulatory Analyst
Conformity of production (COP) is the duty to show that every product built after a type approval still matches the design that was approved. For vehicles and vehicle parts, the approval authority audits the manufacturer’s quality system and tests production samples for as long as the product is made. If production drifts, it can withdraw the approval.
Key points
- An approval covers a design, not every unit: Conformity of production is the proof, kept up for as long as the product is made, that each unit matches what was approved.
- COP is a continuing duty, not a one-time audit: UN and EU authorities can check at any time, at a risk-based frequency of at least once every three years.
- Drift is a failure even when the product still performs: An unreported change of supplier, material or process breaks conformity, so change control is what auditors look at hardest.
- One failure can reach every market at once: A withdrawn approval can affect every market that recognized it, and Commission fines in the EU can reach €30,000 per non-compliant vehicle.
- The US works differently: Manufacturers certify their own vehicles for safety, and agencies check afterward through inspections, audits and recalls.
What is conformity of production?
Conformity of production is a manufacturer’s ongoing proof that the units it builds match the approved type, meaning the design an authority tested and certified. The approval shows that a design met the rules once, and COP covers every unit made after that.
A common misconception is that COP means the audit an authority runs before granting the approval. That audit is only the start. Conformity of production lasts as long as the approved product is made, and the authority can check it at any time.[1]
The idea isn’t unique to vehicles. Under the EU Medical Devices Regulation, Regulation (EU) 2017/745, a notified body (an independent assessor designated by an EU country) audits the manufacturer’s quality system at least once every 12 months. It also runs unannounced audits at least once every five years and tests samples from production.[2] In the US, the Environmental Protection Agency (EPA) can order a selective enforcement audit of engines taken from the production line, and it can suspend the certificate for a whole engine family that fails.[3]
The rest of this article covers vehicles and vehicle parts, where the term comes from. Two texts set the rules. Schedule 1 of the United Nations 1958 Agreement governs approvals granted under UN Regulations. The EU’s own vehicle approval framework, Regulation (EU) 2018/858, has applied since September 1, 2020.[4]
Who is responsible for conformity of production?
The manufacturer that holds the approval is responsible, and the approval authority checks. Regulation (EU) 2018/858 makes the manufacturer answerable to the authority for conformity of production. It must have procedures that keep series production in line with the approved type.[4]
The approval authority often works through a technical service, which is a test or audit body it designates to act for it. Outsourcing doesn’t move the duty. Consider a brand that holds an approval for a component made under contract elsewhere. The contract manufacturer builds it, but the brand answers to the authority for every unit.
The table below separates the checks that newcomers often treat as one.
| Layer | Who | When | What it covers |
|---|---|---|---|
| Manufacturer’s own controls | Manufacturer | Continuously | Quality system, control plans, routine tests, change control |
| Initial assessment | Approval authority or its technical service | Before approval is granted | Whether the quality system and product checks are adequate |
| Continued verification | Approval authority or its technical service | After approval, at a risk-based frequency | Audits, records, sample tests against approved values |
| Market surveillance | National authorities; in the EU, also the European Commission | After sale | Documents and tests of products on the market |
Under both the UN and EU rules, COP always has two parts. One is an assessment of the quality management system. The other is a check of the product conformity arrangements, meaning the tests and inspections that show each product matches the type.[1, 4]
Does ISO 9001 or IATF 16949 replace a COP audit?
Only in part. An authority may accept an ISO 9001 certificate for the initial assessment of the quality system if the certificate’s scope covers the products.[1, 4] The EU text also names ISO/TS 16949, the automotive standard since replaced by IATF 16949, or an equivalent. These are industry standards, not laws. A certificate covers the management system but not whether the parts on the line match the approved type, so the authority still checks that and keeps verifying after approval.
What do manufacturers need in place for conformity of production?
A manufacturer needs documented controls, agreed with the authority, that show each unit matches the approved type, and records that prove it.[4]
- Control plans: These set which tests and checks run at what intervals, and they’re agreed with the authority before approval.
- Test equipment: The manufacturer needs access to the equipment the checks require. Auditors will also ask for calibration records, since a result from an uncalibrated rig proves little.
- Records: Test results must be recorded, analyzed for stability and kept for the period agreed with the authority, up to 10 years.
- Response to failures: A failed sample triggers more sampling and testing and steps to bring production back to the approved type.
- Traceability and change control: The manufacturer must be able to link each unit to the design version and parts it was built with, and to catch changes before they reach production. The law doesn’t set these out as separate duties, but no audit or recall works without them.
How do product changes affect conformity of production?
Any change that makes production differ from the approved type is a COP problem until the approval is updated, even if every unit still performs well.
Under Regulation (EU) 2018/858, the manufacturer must tell the approval authority without delay about any change to the information package, the documents that describe the approved type. The authority then decides whether the change needs a simple revision, an extension backed by further tests, or a new approval.[4] The 1958 Agreement requires the issuing authority to withdraw an approval, temporarily or permanently, when production doesn’t match the information document or the COP conditions and the problem isn’t put right within six months.[1]
A part that performs just as well is still a nonconformity if it isn’t the part that was approved. These changes rarely come from engineering. They come from purchasing dual-sourcing a component, from a supplier switching material or moving a line, or from a process tweak on the shop floor. Supplier contracts that require notice before changes, and one named owner who decides what must be reported, matter as much as the test lab.
Changes in the law matter too. An EU approval becomes invalid when new requirements become mandatory for the type and the approval can’t be extended to cover them.[4] Working out which approved products a new requirement touches, in every market where they’re sold, is its own job. Daptic tracks regulatory changes across jurisdictions and flags the ones that affect a company’s products, so a team can see early which approvals may need an extension.
What do authorities check after type approval?
After approval, authorities audit the plant and quality system, test samples, check records and, once products are sold, test them on the market. These checks don’t follow a fixed calendar.
Audits: The authority may check the manufacturer’s control methods at any time. Under both the UN and EU rules, it sets the frequency through a risk assessment, with a minimum of once every three years.[1, 4] A complaint or a market test result can bring an earlier visit, and EU manufacturers must review complaints and keep a record of them.[4]
Sampling and testing: Inspectors may pick samples at random and have them tested in the manufacturer’s lab or by the technical service. Where a test allows a range of values, the EU authority picks the values at random.[1, 4] These framework texts don’t set pass or fail thresholds. Each UN Regulation or EU technical act sets its own tests, tolerances and statistical sampling rules.
Documents: For whole vehicles, the authority checks a statistically relevant number of vehicles and their certificates of conformity, the document each vehicle carries declaring that it matches the approved type.[1, 4]
Products on the market: Each EU country must test at least one vehicle for every 40,000 new motor vehicles registered there the year before, with at least five tests a year. Where a country runs more than five, at least 20% of the minimum must be emissions tests. The Commission can also run its own tests.[4] Emissions rules add in-service conformity checks of vehicles already in use.[5]
What happens when production doesn’t conform?
The authority first requires the manufacturer to restore conformity. If that fails, it can withdraw the approval, and recalls and penalties can follow.
Correction: The authority must make sure the manufacturer restores conformity as rapidly as possible. In practice, that means a corrective action plan and closer checks.[4]
Withdrawal: If production still doesn’t conform, the EU authority can withdraw the approval, which ends its validity.[4] Withdrawing an approval cancels the certificate, which is different from withdrawing products from the market.
Recall: A manufacturer must act immediately on non-compliant products already sold, bringing them into conformity or withdrawing or recalling them, and must inform the authority. Authorities can order these measures if it doesn’t.[4]
Penalties: EU countries set their own penalties, which must cover false declarations, falsified test results and withholding data that could lead to a recall. The Commission can fine up to €30,000 per non-compliant vehicle, system, component or separate technical unit.[4]
A problem at one plant rarely stays in one country. Countries applying the same UN Regulation recognize each other’s approvals, so a withdrawal can affect every market that relied on the approval. In the EU, other authorities can refuse to recognize an approval they find non-compliant.[1, 4]
How does conformity of production differ in the US and Japan?
The UN and EU systems have an authority check production both before and after approval. In the US, manufacturers certify their own products and agencies check afterward. The table summarizes the main approaches.
| Market | Who confirms the design | How production is checked |
|---|---|---|
| EU | Approval authority | Initial assessment, risk-based audits and sample tests, market surveillance |
| UN 1958 Agreement countries | Authority granting the UN approval | Schedule 1: initial assessment and continued verification |
| US, vehicle safety | Manufacturer self-certifies | NHTSA inspections and investigations, recalls, civil penalties |
| US, emissions | EPA certificate of conformity | Selective enforcement audits, in-use testing |
| Japan | MLIT | Schedule 1 for UN approvals; national rules for type designation |
United States: Vehicle safety has no approval. A manufacturer certifies that each vehicle meets the Federal Motor Vehicle Safety Standards, and it may not certify if, exercising reasonable care, it has reason to know the certificate is false. The National Highway Traffic Safety Administration (NHTSA) can inspect plants, records and vehicles. A manufacturer that decides a product doesn’t comply must notify NHTSA and owners and fix the problem.[6–8] Civil penalties reach $27,874 per violation and $139,356,994 for a related series of violations.[9] For emissions, EPA certifies before sale and checks afterward through audits. Light-duty vehicles also get in-use testing, at 10,000 miles or more and again at 50,000 miles or more.[3, 10]
Japan: Japan acceded to the 1958 Agreement in November 1998, so the UN approvals it grants follow Schedule 1.[11] Its Ministry of Land, Infrastructure, Transport and Tourism (MLIT) also runs a national type designation system with its own rules.
What should a manufacturer be able to show at a COP audit?
A manufacturer should be able to show that what it builds today matches what was approved, and how it knows.
- Match each product in production to its approval and the current information package.
- Produce the agreed control plans and records showing that the checks ran on schedule.
- Trace a unit from its serial or batch number to its design version and part suppliers.
- Show calibration records for the test equipment.
- List every design, supplier and process change since the last audit, and show which ones were reported.
- Show how failed samples and complaints were investigated and closed.
Example: a supplier changes a component
Here is how this applies to one product. Consider a manufacturer that holds EU and UN approvals for a seat assembly. Its bracket supplier moves to a second plant and, to cover a shortage, switches steel grade without telling anyone. The brackets keep passing incoming inspection and the routine strength test.
The first question is whether the change touches the approved type. If the information package specifies the bracket’s material or drawing, production no longer matches it, whatever the test results say. The manufacturer should quarantine the affected stock and trace which assemblies carry the new bracket and where they went. It should also confirm whether those assemblies still meet the technical requirements.
Next, it tells the approval authority without delay. The authority then decides on a revision, an extension with tests or a new approval. If non-compliant units have already been sold, the recall question opens.
If the authority finds the change first, at an audit or through a market test, the same facts become a finding. That brings a corrective action plan, closer checks and a risk to the approval in every market. What prevents a repeat is contractual: a duty on suppliers to give notice before changing material, process or site.
Frequently asked questions
Is conformity of production a one-time audit?
No. The initial assessment comes before approval, but the duty lasts as long as the product is made, and the authority can check at any time.
How often do authorities audit conformity of production?
The UN and EU rules set no fixed schedule. Frequency is based on risk, with a minimum of once every three years, and a complaint or market test result can bring an earlier check.
Does IATF 16949 certification replace a conformity of production audit?
No. An authority may accept a quality system certificate for the initial assessment, but it still checks the product conformity arrangements and keeps verifying after approval.
Can a supplier change cause a conformity of production failure?
Yes. If production no longer matches the approved type, it’s a nonconformity even when the product still performs, until the authority has been told and has amended the approval.
Is there conformity of production in the US?
Not in the same form. Vehicle manufacturers certify their own compliance with the safety standards and NHTSA checks after sale, while EPA uses audits and in-use testing for emissions.
Notes and sources
- 1958 Agreement, Revision 3 (E/ECE/TRANS/505/Rev.3), UNECE, particularly Articles 3 and 4; Article 2(1) and Schedule 1, paragraph 3.1; paragraphs 1.1 and 2.2; paragraph 1.3.3; paragraphs 3.1 and 3.1.1.2; paragraph 3.3.
- Regulation (EU) 2017/745 (Medical Devices Regulation), particularly Annex IX, sections 3.3 and 3.4.
- 40 CFR Part 1068, Subpart E, selective enforcement auditing, particularly §§ 1068.401, 1068.405 and 1068.430.
- Regulation (EU) 2018/858 on the approval and market surveillance of motor vehicles, particularly Articles 8, 9, 13, 14(1), 31, 33(1), 34, 35(2)(a), 52–54, 84, 85(1) and 91; Annex IV, points 1.1 and 1.2; Annex IV, point 2.3.3; Annex IV, points 3.2 and 3.3.1 to 3.3.6; Annex IV, points 4.1 and 4.1.1.2; Annex IV, point 4.5, and Articles 31(7) and 35(2)(d).
- Regulation (EU) 2017/1151 on emissions type approval, particularly Article 9 and Annex II.
- 49 U.S.C. 30115, certification of compliance, particularly § 30115(a).
- 49 U.S.C. 30166, inspections, investigations and records, particularly § 30166(b).
- 49 U.S.C. 30118, notification of defects and noncompliance, particularly § 30118(c).
- 49 CFR 578.6, civil penalty amounts, particularly § 578.6(a)(1).
- 40 CFR 86.1845-04, manufacturer in-use verification testing, particularly § 86.1845.
- MLIT, notice on the expansion of reciprocal recognition under the 1958 Agreement (June 2000)
Additional sources:
This article reflects Michelle Ng’s independent opinions, not necessarily those of Daptic.



