EU End-of-Life Vehicles Regulation: what replaces the ELV Directive

Marc HaddadForward Deployed Regulatory Engineer
The EU End-of-Life Vehicles Regulation, Regulation (EU) 2026/1738, replaces the End-of-Life Vehicles (ELV) Directive 2000/53/EC and the recyclability type-approval Directive 2005/64/EC. It was adopted on July 8, 2026, entered into force on August 13, 2026, and applies from September 1, 2028. Its main design requirements apply to vehicle types approved from September 1, 2032.
Key points
- The ELV Regulation is adopted law, published in the Official Journal on July 24, 2026, so figures quoted from the Commission’s 2023 proposal are out of date.
- It moves obligations upstream to vehicle design and type approval. Most design requirements apply to vehicle types approved from September 1, 2032.
- New vehicle types need at least 15% recycled plastic from September 1, 2032, and 25% from September 1, 2036, with at least a fifth of that target coming from end-of-life vehicles.
- Trucks, buses, trailers and motorcycles come into scope on September 1, 2031, mostly for end-of-life duties rather than design rules.
What does the ELV Directive do, and why is the EU replacing it?
The ELV Directive sets EU rules for passenger cars (category M1) and light commercial vehicles (category N1) at the end of their life, and it binds vehicle makers until September 1, 2028. It covers treatment, reuse, recycling and recovery targets, collection, heavy metal limits and a basic form of extended producer responsibility, meaning producers pay part of the cost of collecting their vehicles once they are scrapped.[1] A second law, Directive 2005/64/EC, made recyclability part of type approval, the procedure in which an authority certifies a vehicle type before it can be sold.[1]
The EU’s evaluation found that the Directive worked on heavy metals but did little for design, because its design provisions were not detailed, specific or measurable enough. It also left too many vehicles unaccounted for at collection.[1] Each member state had to write both directives into its own national law, so the EU replaced them with a regulation, which applies directly and the same way in every member state.[1]
Where does the End-of-Life Vehicles Regulation stand now?
The Regulation is adopted and in force, and nothing is left to negotiate between Parliament and Council. The Commission proposed it on July 13, 2023. Parliament adopted its position on June 18, 2026, the Council adopted the act on June 29, 2026, and it was published on July 24, 2026.[2] It entered into force on August 13, 2026, and applies from September 1, 2028, when the ELV Directive is repealed.[1]
The open work now sits with the Commission, which owes the method for counting recycled content by August 31, 2028, and a new recyclability calculation method by February 28, 2029. It also owes the passport’s technical rules by August 14, 2030.[1] Until those acts exist, nobody can say exactly how recycled content will be counted. Daptic tracks regulatory changes such as these acts across jurisdictions, flags the ones that affect your products and works out which requirements apply to each vehicle or part in each market.
The table below lists the dates that matter, past and future.
| Date | Milestone | Status |
|---|---|---|
| July 13, 2023 | Commission proposal, COM(2023) 451 | Proposed, superseded by the adopted text |
| June 29, 2026 | Council adopts the Regulation after Parliament’s June 18 vote | Adopted |
| July 24, 2026 | Published as Regulation (EU) 2026/1738 | Published |
| August 13, 2026 | Entry into force; vehicle battery restrictions move to Regulation (EU) 2023/1542 | In force |
| September 1, 2028 | Regulation applies; Directive 2000/53/EC repealed | Adopted |
| September 30, 2028 | Steel and aluminium recycled-content targets due by delegated act | Due, not yet adopted |
| September 1, 2029 | Circularity strategy, dismantling information, producer responsibility | Adopted |
| January 1, 2030 | 95% reuse and recovery, 85% reuse and recycling targets for end-of-life vehicles | Adopted |
| September 1, 2031 | Scope extends to M2, M3, N2, N3, O and L categories; export roadworthiness check | Adopted |
| August 31, 2032 | Directive 2005/64/EC repealed; last day of the ELV Directive’s heavy metal exemptions | Adopted |
| September 1, 2032 | New types: recyclability, 15% recycled plastic, substances, removability; passport for each vehicle | Adopted |
| August 14, 2033 | Latest date for steel and aluminium targets to apply | Expected, figures not set |
| September 1, 2036 | 25% recycled plastic for new types | Adopted |
Which vehicles does the ELV Regulation cover?
The Regulation covers cars and vans first and extends to buses, trucks, trailers and L-category vehicles such as motorcycles from September 1, 2031. Most design requirements stay with cars and vans.[1] The table shows which design requirements (Articles 4 to 13) reach each category.
| Category | Covered from | Design requirements that apply |
|---|---|---|
| M1 and N1 (cars and vans) | September 1, 2028 | All, mostly for types approved from September 1, 2032 |
| Special purpose M1 and N1 (for example motor caravans) | September 1, 2029 | Substance restrictions (Article 5) only |
| M2, M3, N2, N3 and O (buses, trucks, trailers) | September 1, 2031 | Limited removal and information duties (Articles 7 and 11) |
| L category (motorcycles, mopeds, quadricycles) | September 1, 2031 | Limited removal, information and coding duties (Articles 7, 8, 11 and 12) |
Several groups fall outside the Regulation entirely: small-series vehicles, armed-services vehicles, historic vehicles, vehicles recognized as being of special cultural interest, and trailer caravans.[1]
What does the ELV Regulation require of vehicle manufacturers?
Most design requirements attach to the vehicle type at type approval and apply to types approved from September 1, 2032, not to every vehicle built after that date. Manufacturers meet them in this order:
- Circularity strategy: from September 1, 2029, each manufacturer writes a company-level strategy, sends it to type-approval authorities and the Commission, and updates it every five years.[1]
- Dismantling and repair information: from September 1, 2029, manufacturers give treatment facilities, technical publishers and repairers free access to information on removing and replacing parts, including electric vehicle batteries, though they may charge reasonable fees that cover their administrative costs.[1]
- Recyclability: vehicles of types approved from September 1, 2032, must be at least 85% reusable or recyclable and 95% reusable or recoverable by mass, the rates Directive 2005/64/EC already used. Manufacturers must collect and verify supplier data to prove it.[1]
- Substances: those types, and new parts for them, must not contain lead, mercury, cadmium or hexavalent chromium beyond the exemptions in Annex IV.[1]
- Removability: those types must allow listed parts to be removed. Electric vehicle batteries and e-drive motors must be removable and replaceable without damage, and software updates may not block this.[1]
- Digital Circularity Vehicle Passport: from September 1, 2032, each vehicle placed on the market carries a passport with dismantling information, the exemptions used, recycled content and the spare parts catalogue.[1] This is the one design-stage duty tied to each vehicle rather than to new types.
The evidence goes into the type-approval information folder under Regulation (EU) 2018/858. From September 1, 2032, a circularity entry joins that Regulation’s list of approval requirements. Until August 14, 2032, the recyclability check runs under Directive 2005/64/EC.[1]
What are the ELV Regulation’s recycled content requirements?
All the plastic in a vehicle type approved from September 1, 2032, counted together, must include at least 15% recycled plastic by weight from post-consumer waste, rising to 25% from September 1, 2036. At least 20% of that target must come from end-of-life vehicles or from parts removed during use.[1] Tyre elastomers and most thermosets are left out of the calculation. Recycled plastic counts only if it comes from an installation in the EU or, from August 14, 2030, from an audited installation outside the EU that meets the Regulation’s criteria.[1]
These are the adopted figures. The Commission’s 2023 proposal asked for 25%, with a quarter of it from end-of-life vehicles, so a page quoting those numbers is quoting a text that never became law.[3] The Commission must assess by August 14, 2031, whether manufacturers are on track, and may then propose changes.[1]
The steel and aluminium targets have not been set yet. Once each counting method has been in place for 12 months, manufacturers must also declare recycled content for each new type, covering steel, aluminium, magnesium, plastics and certain magnet materials. For each plastic component over 100 grams, they must say whether the recycled material is pre-consumer or post-consumer.[1]
What happens to the ELV Directive’s hazardous substance rules?
The substance rules carry over, with a long transition. The Directive’s heavy metal ban and its Annex II exemptions apply until August 31, 2032, except four entries that stopped applying on August 13, 2026, when the restrictions on vehicle batteries moved into the Batteries Regulation (EU) 2023/1542.[1] For new types from September 1, 2032, the Regulation’s own ban and its Annex IV exemptions take over.
The limits are 0.1% by weight for lead, hexavalent chromium and mercury and 0.01% for cadmium. They are measured in each homogeneous material, meaning a single material that cannot be mechanically separated into different materials.[1] The Regulation also asks for “substances of concern” to be kept to a minimum. It requires a Commission report by February 14, 2028, on the ones that hinder recycling and lets the Commission restrict them by delegated act.[1] REACH, the EU’s main chemicals regulation, and the Persistent Organic Pollutants (POPs) Regulation apply alongside it.
What does extended producer responsibility mean under the ELV Regulation?
From September 1, 2029, producers pay for collecting and treating their vehicles at the end of their life. A producer is any manufacturer, importer or distributor that first makes a vehicle available in a member state on a professional basis, whatever the selling technique.[1]
Producers register in each member state where they first place vehicles, and they cannot sell there unless registered. A producer can meet its duties on its own, backed by a financial guarantee, or through a producer responsibility organization (PRO). PRO fees vary with weight, recyclability, dismantling time, recycled content and restricted substances.[1]
Manufacturers of M1 and N1 vehicles must also appoint an authorized representative in each member state. The representative covers vehicles scrapped there that have no identifiable producer.[1] Collected vehicles must be treated to reach 95% reuse and recovery and 85% reuse and recycling from January 1, 2030, and 30% plastics recycling from January 1, 2032.[1]
When is a used vehicle an end-of-life vehicle?
Annex I sets the test. A vehicle that has been cut up, burnt or flooded above the dashboard, or has key components beyond repair, is waste. Indicative signs, such as repair costs that, added to the vehicle’s current value, exceed its estimated market value after repair, trigger a technical assessment.[1] From September 1, 2031, only roadworthy used vehicles may be exported, and customs must have each one’s vehicle identification number (VIN). Customs checks it automatically against national registers once those systems are linked up.[1]
Where does the ELV Regulation get complicated for parts suppliers?
Most articles name manufacturers, but much of the work lands on suppliers.
- Coding is your own duty: manufacturers and their suppliers must code parts and materials using the standards listed in Annex VII.[1]
- The target applies to the vehicle type, not to each part: the 15% and 25% apply across all the plastic in a vehicle type. Your customer decides which parts carry recycled plastic, and a large part with no safety function may be asked for far more than 15%.
- The vehicle type’s approval date decides, not your production date: parts for a type approved before September 1, 2032, fall outside the recycled-content, recyclability and removability articles even if they are built in 2035. The same part fitted to a newly approved type falls inside them.
- Substances in carry-over types need a closer read: the Directive’s ban ends on August 31, 2032, and the Regulation’s ban is written around new types. Several Annex IV entries still refer to older types and spare parts, so check each entry’s scope column.
What should a compliance team do now?
- Map what you place on the EU market: vehicle makers list their categories. Suppliers list each part number and the vehicle types it goes into, and compare them against the dates above.
- Find your material and substance data: for each part, record the polymer, mass, recycled share and where the recycled material came from. Add homogeneous-material data for the four heavy metals.
- Plan around type approvals: find which vehicle types will be approved from September 1, 2032, and work back to recycled plastic sourcing, because qualifying a new grade takes time.
- Prepare for producer responsibility: if you place vehicles on the market, choose between meeting the duties yourself or through a PRO, and plan registration before September 1, 2029.
Example: applying the ELV Regulation to a plastic interior parts supplier
A supplier molds polypropylene door trim for two car makers. One customer’s platform was type approved in 2027, and the other plans to approve a new platform in 2033. This is a composite case.
Parts for the 2027 platform carry no recycled-content or recyclability obligation under the Regulation. The 2033 vehicle type needs at least 15% post-consumer recycled plastic across all its plastic, and at least a fifth of that must come from end-of-life vehicles or from parts removed during use. The customer asks for 30% in door trim, because the parts are large and have no safety function.
For each part, the supplier records the grade, the recycled share, the post-consumer origin (every part is over 100 grams) and the recycling installation. A compound recycled outside the EU counts only from August 14, 2030, and only from an audited installation. The supplier codes the parts to Annex VII and supplies homogeneous-material data, including for colorants and additives. It has no registration duty as a producer, because it does not make vehicles available on the market.
Frequently asked questions
Is the ELV Directive still in force?
Yes, until August 31, 2028. Directive 2000/53/EC is repealed from September 1, 2028, but its heavy metal ban and Annex II exemptions continue until August 31, 2032.
When does the EU End-of-Life Vehicles Regulation apply?
The Regulation applies from September 1, 2028, after entering into force on August 13, 2026. Producer responsibility starts on September 1, 2029, and the design requirements apply to vehicle types approved from September 1, 2032.
How much recycled plastic will new cars need?
New vehicle types approved from September 1, 2032, need at least 15% post-consumer recycled plastic, rising to 25% from September 1, 2036. At least 20% of that target must come from end-of-life vehicles or from parts removed during use.
Does the ELV Regulation apply to trucks, buses and motorcycles?
Yes, from September 1, 2031, but most design requirements, including recycled content and the passport, do not apply to them.
Do parts suppliers have obligations under the ELV Regulation?
Yes. Suppliers must code parts and materials to the Annex VII standards. Manufacturers must also collect and verify their suppliers’ data to show that each vehicle type meets the design requirements.
Notes and sources
- Regulation (EU) 2026/1738 (ELV Regulation), OJ L, 2026/1738, July 24, 2026, particularly Articles 2(2), 3–11, 13, 17, 19–22, 33, 39, 40, 46(4), 53, 55, 56(6), 57 and 59; recitals 3 and 10; recital 5; recitals 4, 8 and 19; Article 2(1) and (3) to (6); Article 6(1) to (4); Article 5(1) to (3); Article 37 and Annex I; Article 12(1) and Annex VII.
- European Parliament, Legislative Observatory, procedure 2023/0284(COD))
- European Commission, COM(2023) 451, proposal for a Regulation on circularity requirements for vehicle design and on management of end-of-life vehicles, particularly Article 6.
Additional sources:
This article reflects Marc Haddad’s independent opinions, not necessarily those of Daptic.



