How to get CE marking: a step-by-step guide for manufacturers

Michelle NgSenior Regulatory Analyst
CE marking shows that a manufacturer has assessed a product and declared that it meets applicable European Union (EU) requirements. Obtaining the mark involves identifying relevant legislation, demonstrating conformity, preparing technical documentation, and signing an EU declaration of conformity. Some products also require an independent assessment by a notified body before the mark can be applied.
Key points
- CE marking is the manufacturer’s claim of conformity: It is not a quality certification or a certificate manufacturers can simply purchase.
- Not every product requires it: CE marking applies only to products covered by legislation requiring the mark.
- Third-party assessment is not always mandatory: Many products can be assessed by the manufacturer.
- Documentation supports conformity: Manufacturers must maintain evidence demonstrating how requirements were satisfied.
- Compliance continues after launch: Changes to products, standards, or legislation may require reassessment.
What is CE marking?
CE marking indicates that a manufacturer takes responsibility for a product’s conformity with the applicable EU legislation requiring the mark. It is used for various product categories, including electrical equipment, machinery, toys, and medical devices.
A common misconception is that CE marking means a product has been independently tested and approved by an EU authority. That is not necessarily the case. For many products, the manufacturer performs or arranges the conformity assessment (the checks that show a product meets the law) and declares compliance without mandatory third-party certification.
CE marking is the result of demonstrating conformity, not a separate approval that manufacturers purchase.
Step 1: Which EU laws apply to the product?
The first step is identifying which directives and regulations apply to the product. A directive applies through each EU country’s own law, while a regulation applies directly. Different laws address different risks or characteristics. For example:
| Legislation | Main focus |
| Low Voltage Directive 2014/35/EU | Electrical safety for equipment within specified voltage limits |
| Electromagnetic Compatibility Directive 2014/30/EU | Electromagnetic emissions and immunity |
| Radio Equipment Directive 2014/53/EU | Radio equipment safety, compatibility, and spectrum use |
| Restriction of Hazardous Substances Directive 2011/65/EU | Restricted substances in electrical and electronic equipment |
A product may fall under several laws, but not every law applies to every electrical product. Some legislation addresses particular risks in place of other directives. For example, radio equipment meets its safety and electromagnetic compatibility requirements under the Radio Equipment Directive, instead of the Low Voltage and Electromagnetic Compatibility Directives.
The manufacturer’s intended use, technical characteristics, and product functions determine which requirements apply. This is why CE marking begins with understanding the product rather than selecting a test laboratory.
Step 2: What are harmonized standards?
Harmonized standards are European standards developed under a request from the European Commission whose references are published in the Official Journal of the European Union under specific legislation. They provide recognized technical methods for demonstrating conformity with the legal requirements they cover. For example, an electrical safety standard may establish test methods and criteria for evaluating relevant hazards.
However, a standard is not the same as a law. Legislation establishes the mandatory requirements, while harmonized standards provide a voluntary way to demonstrate conformity. Using an applicable harmonized standard can provide a presumption of conformity for the requirements it covers.
A standard may address only part of the legislation. Meeting one standard does not necessarily establish conformity with every requirement.[1]
Step 3: Is a notified body required?
A notified body is an organization that an EU country has designated, and notified to the European Commission, to perform specific conformity assessment activities under EU legislation. Some products can follow a manufacturer-led assessment procedure, often called self-declaration. Others require notified body involvement, depending on the legislation and available assessment route. Each law lists the assessment routes, called modules, that a manufacturer may use.[1]
For example, the Low Voltage Directive allows manufacturers to assess conformity themselves, without a notified body. Certain procedures under the Radio Equipment Directive require notified body involvement, depending on the technical requirements, the standards applied, and the selected conformity assessment route.
The European Commission maintains the New Approach Notified and Designated Organisations (NANDO) database, which identifies notified bodies and their authorized activities.[2] A laboratory performing product testing is not automatically a notified body.
Step 4: What is technical documentation?
Technical documentation is the collection of evidence showing how a product meets applicable requirements. It may include design information, product specifications, risk assessments, test reports, drawings, and identification of the standards used.
For manufacturers, this documentation explains the relationship between the product’s design and the legal requirements it must satisfy. A test report alone may not be enough. The documentation should provide a broader picture of how conformity was evaluated. Technical documentation must be ready before the product is placed on the EU market, meaning first made available for sale or use there.[1]
Step 5: What is the EU declaration of conformity?
The EU declaration of conformity (DoC) is the manufacturer’s formal statement that the product meets the applicable EU requirements. It identifies the product, manufacturer, relevant legislation, and standards or technical specifications used. It must include other information required by the applicable laws and be signed by an authorized person.
Where several EU laws require a declaration, the manufacturer must draw up a single DoC covering all of them. Signing it represents the manufacturer’s acceptance of responsibility for the product’s declared conformity.[3]
Step 6: When can the CE mark be applied?
The CE mark can be affixed after the manufacturer completes the required conformity assessment and prepares the necessary documentation. It must be visible, legible, and indelible, with a minimum height of 5 millimeters unless specific legislation provides otherwise.[4]
The mark normally appears on the product or its data plate. Certain laws permit alternative placement where marking the product is not possible or warranted. When the applicable assessment procedure requires it, the notified body’s identification number must accompany the mark.
Step 7: Does a non-EU manufacturer need an EU-based economic operator?
Certain products must have an economic operator (a business in the supply chain) established in the EU under Article 4 of Regulation (EU) 2019/1020. This may be an EU-based manufacturer, importer, authorized representative, or fulfillment service provider.
This operator performs specified responsibilities related to documentation and cooperation with market surveillance authorities. Its name and contact details, including a postal address, must appear on the product, its packaging, the parcel, or an accompanying document.
The requirement does not apply to every CE-marked product, and the operator’s responsibilities depend on the applicable legislation. It covers products under the laws listed in Article 4(5), including the rules for electrical and radio equipment, toys, machinery, and personal protective equipment. Article 16 of the General Product Safety Regulation (GPSR) establishes similar EU-based economic operator requirements for consumer products that no specific EU product law covers.[5]
What happens after CE marking?
CE marking does not remove the manufacturer’s responsibility to ensure that products continue to meet applicable requirements. Changing a component, product design, or software function may affect the original conformity assessment. Manufacturers may also need to reconsider their assessment when legislation changes or when a harmonized standard they relied on is revised or withdrawn. For example, the Machinery Regulation replaces the Machinery Directive on January 20, 2027, and the Cyber Resilience Act applies in full from December 11, 2027.[6]
Technical documentation must be retained for the period established by the applicable legislation. For example, the Low Voltage Directive and Electromagnetic Compatibility Directive require manufacturers to retain the technical documentation and DoC for 10 years after the product is placed on the market.[7]
Is CE marking accepted in the UK?
Great Britain (England, Scotland, and Wales) continues to accept CE marking for many product categories, including electrical equipment, alongside UK Conformity Assessed (UKCA) marking. The UK has extended CE recognition indefinitely for many covered sectors. However, requirements are not identical across all product categories, and the applicable product-specific rules must still be met. Northern Ireland follows EU rules, so products there carry the CE mark, plus a UKNI mark where a UK-based body did a required third-party assessment.[8]
Frequently asked questions
Can manufacturers CE mark products themselves?
Yes, where the applicable legislation permits manufacturer-led conformity assessment.
Is CE marking required for all products sold in the EU?
No. Only products covered by legislation requiring CE marking must carry it.
Does CE marking require laboratory testing?
Not always. The necessary evidence depends on the product and applicable conformity assessment procedure.
Does CE marking expire?
No. There is no general expiration date for the CE mark, but certificates under certain assessment procedures may expire and changes may require reassessment.
Can one CE mark cover multiple EU directives?
Yes. One mark covers every applicable EU law that requires CE marking.
Notes and sources
- European Commission — Blue Guide on EU Product Rules (2022).
- European Commission — Notified Bodies and NANDO. See also the NANDO database.
- Decision No 768/2008/EC, including the conformity assessment modules and model declaration provisions. The single-declaration rule is in Annex I, Article R10(3), and in each aligned law, for example the Low Voltage Directive 2014/35/EU, Article 15(3).
- Regulation (EC) No 765/2008 (consolidated text as amended to July 16, 2021), Article 30 and Annex II.
- Regulation (EU) 2019/1020 (consolidated text as amended to August 12, 2026), Article 4. See also Regulation (EU) 2023/988 (GPSR), consolidated text as amended to May 29, 2026, Articles 2(1) and 16.
- Machinery Regulation (EU) 2023/1230 (consolidated text as amended to July 27, 2026), Article 54; Cyber Resilience Act, Regulation (EU) 2024/2847 (consolidated text with corrections), Article 71.
- Low Voltage Directive 2014/35/EU (consolidated text as amended to May 30, 2026), Article 6; Electromagnetic Compatibility Directive 2014/30/EU (consolidated text as amended to May 30, 2026), Article 7.
- UK Government — Placing UKCA or CE marked products on the market in Great Britain; UK Government — Sector-specific product marking; UK Government — Placing CE or CE and UKNI marked products on the market in Northern Ireland.
Additional sources:
- Radio Equipment Directive 2014/53/EU (consolidated text as amended to May 30, 2026) and RoHS Directive 2011/65/EU (consolidated text as amended to July 1, 2026).
This article reflects Michelle Ng’s independent opinions, not necessarily those of Daptic.



