Daptic announces $22M funding to bring compliance into product development. Learn More
Request Demo
Expert Authored

EU General Safety Regulation (GSR2): which safety systems are mandatory, and when

GSR2 explained: the safety systems the EU General Safety Regulation requires on cars, vans, trucks and buses, and when each becomes mandatory.
A card titled GSR2 Registration Dates listing four dates from July 2022 to January 2029, with January 7, 2029 marked as the deadline, over soft green bands.
November 19, 2026

Marc HaddadMarc HaddadForward Deployed Regulatory Engineer

 

The EU General Safety Regulation, Regulation (EU) 2019/2144 (GSR2), sets the safety systems a car, van, truck or bus must have before it can be type approved or registered in the EU. Each system has two dates: an earlier one for new vehicle types and a later one for every newly registered vehicle.

 

Key points

 

  • GSR2 has applied since July 6, 2022. It has one list of systems for every motor vehicle, a second for cars and vans, and a third for buses and trucks.
  • Most systems became mandatory on every newly registered vehicle on July 7, 2024, and a second group, including driver distraction warning, followed on July 7, 2026.
  • The last registration date is January 7, 2029, when direct vision and event data recorders become mandatory on every new bus and truck.
  • An older type approval does not carry a model past a registration date, and unsold vehicles that miss it need an end-of-series derogation.
  • Each system is proven at type approval against a UN Regulation or an EU delegated or implementing act, and those acts keep being amended.

What is the EU General Safety Regulation (GSR2)?

 

GSR2 is the EU regulation that lists the safety equipment a motor vehicle needs for EU type approval. It replaced the 2009 General Safety Regulation, Regulation (EC) No 661/2009, along with the separate pedestrian and hydrogen regulations, and it has applied since July 6, 2022.[1]

 

Type approval is the procedure in which a national approval authority certifies that a vehicle type meets every requirement that applies to it, under the framework of Regulation (EU) 2018/858.[2] GSR2 names each system, the vehicle categories and the dates, then points to a UN Regulation or an EU delegated or implementing act for the technical detail.[1]

Which vehicles does GSR2 apply to?

 

GSR2 applies to passenger vehicles (category M), goods vehicles (category N) and their trailers (category O), and to the systems, components and separate technical units made for them.[1] Which requirements apply depends on the category, which is set by seats and maximum mass:[2]

 

  • M1: cars, with up to eight seats besides the driver’s.
  • M2 and M3: buses and coaches, up to and above 5 tonnes.
  • N1: vans and other goods vehicles up to 3.5 tonnes.
  • N2 and N3: trucks above 3.5 tonnes, with N3 above 12 tonnes.
  • O3 and O4: trailers above 3.5 tonnes, which GSR2 reaches mainly through tyre pressure monitoring.

 

GSR2’s obligations attach to new vehicles placed on the market, so vehicles already registered don’t have to be retrofitted. There is no general exemption for small production runs. A recital only lets the technical acts take low-volume vehicles into account.[1]

How do the GSR2 dates work?

 

Each requirement carries a letter code in Annex II that sets two dates. From the first, authorities refuse type approval to new types that don’t comply. From the second, a new vehicle that doesn’t comply can’t be registered, because its certificate of conformity stops being valid.[1]

 

A certificate of conformity is the document the manufacturer issues with each vehicle, stating that it matches the approved type, and a vehicle can’t be registered without a valid one.[2] That is how GSR2 reaches models approved years ago. The four codes are:[1]

 

  • A: requirements carried over from the old rules, which apply to all new vehicles from July 6, 2022.
  • B: new types from July 6, 2022, and all new vehicles from July 7, 2024.
  • C: new types from July 7, 2024, and all new vehicles from July 7, 2026.
  • D: new types from January 7, 2026, and all new vehicles from January 7, 2029.

 

As of November 2026, codes A, B and C apply to every new vehicle registered in the EU. Only code D still has a registration date ahead.

Which safety systems are mandatory under GSR2?

 

Every car, van, truck and bus needs intelligent speed assistance, alcohol interlock installation facilitation, driver drowsiness and attention warning, advanced driver distraction warning, an emergency stop signal, reversing detection and an event data recorder.[1] Cars and vans also need emergency braking, emergency lane keeping and an enlarged head impact zone for pedestrians. Buses and trucks also need lane departure warning, emergency braking, detection of pedestrians and cyclists near the front or nearside, and better direct vision from the cab.[1] Tyre pressure monitoring applies across categories.[1]

 

A few of these terms need explaining. Intelligent speed assistance tells the driver, through the accelerator or a warning, when the speed limit is exceeded. Installation facilitation means the vehicle is prepared so an aftermarket alcohol interlock can be fitted. The event data recorder stores crash data from shortly before, during and after a collision.[1]

 

The table shows each system, the categories it applies to, the act that holds its technical requirements, and its two dates.[1]

 

System Applies to Technical requirement New types from All new vehicles from
Intelligent speed assistance All M and N Delegated Regulation (EU) 2021/1958 July 6, 2022 July 7, 2024
Alcohol interlock installation facilitation All M and N Delegated Regulation (EU) 2021/1243 July 6, 2022 July 7, 2024
Driver drowsiness and attention warning All M and N Delegated Regulation (EU) 2021/1341 July 6, 2022 July 7, 2024
Advanced driver distraction warning All M and N Delegated Regulation (EU) 2023/2590 July 7, 2024 July 7, 2026
Emergency stop signal All M and N UN Regulation No 48 July 6, 2022 July 7, 2024
Reversing detection All M and N UN Regulation No 158 July 6, 2022 July 7, 2024
Event data recorder M1, N1 Delegated Regulation (EU) 2022/545; UN Regulation No 160 July 6, 2022 July 7, 2024
Event data recorder M2, M3, N2, N3 Delegated Regulation (EU) 2024/2220; UN Regulation No 169 January 7, 2026 January 7, 2029
Tyre pressure monitoring M1 up to 3,500 kg UN Regulation No 141 Already required July 6, 2022
Tyre pressure monitoring N1 UN Regulation No 141 July 6, 2022 July 7, 2024
Tyre pressure monitoring M2, M3, N2, N3, O3, O4 UN Regulation No 141 July 6, 2022 July 7, 2024
Emergency braking, vehicles and obstacles M1, N1 UN Regulation No 152 July 6, 2022 July 7, 2024
Emergency braking, pedestrians and cyclists M1, N1 UN Regulation No 152 July 7, 2024 July 7, 2026
Emergency lane keeping M1, N1 Implementing Regulation (EU) 2021/646 July 6, 2022 (July 7, 2024 with hydraulic power steering) July 7, 2024 (July 7, 2026 with hydraulic power steering)
Enlarged head impact zone M1, N1 UN Regulation No 127 July 7, 2024 July 7, 2026
Lane departure warning M2, M3, N2, N3, with exemptions UN Regulation No 130 Already required July 6, 2022
Emergency braking M2, M3, N2, N3, with exemptions UN Regulation No 131 Already required July 6, 2022
Pedestrian and cyclist collision warning M2, M3, N2, N3 UN Regulation No 159 July 6, 2022 July 7, 2024
Blind spot information M2, M3, N2, N3 UN Regulation No 151 July 6, 2022 July 7, 2024
Direct vision M2, M3, N2, N3 UN Regulation No 167 January 7, 2026 January 7, 2029

 

Annex II also covers crash protection, lighting, tyres, cybersecurity and automated driving, which are outside this article.

How is each GSR2 system proven?

 

Each system is proven at type approval: a technical service tests it against the cited act, and the approval authority grants the approval. Where GSR2 cites a UN Regulation, an approval to that UN Regulation counts as EU type approval.[1] Intelligent speed assistance, reversing detection and the event data recorder can also be approved as separate technical units, which are parts approved on their own and then fitted to several vehicle types.[1]

 

A supplier’s unit approval helps, but each vehicle type still needs approval for how the system is installed and works in that vehicle. The cited act is the law. A customer specification, an internal test or an industry standard doesn’t replace it unless the act itself calls that standard up.

What do manufacturers and suppliers have to do?

 

Start from the vehicle line, not the regulation. List every type, variant and version with its category and maximum mass, then attach each Annex II row to the versions it applies to.

 

  1. Fix each version’s category: a heavier battery can move a van from N1 to N2, which brings in the bus and truck rows instead of the car and van rows.
  2. Record both dates for each row: note whether the type is new or existing, and plan anything still built after a registration date to meet that row.
  3. Plan the extensions: an approval granted under the old rules stays valid only for requirements GSR2 didn’t change or add, so new systems have to be added through extensions before the registration date.[1]
  4. Agree scope with suppliers: settle which systems arrive with their own approval, and who provides the test data and installation instructions.
  5. Manage stock against each cut-off: plan the run-out of old specifications so few vehicles are left unregistered when a date passes.

 

The evidence has to last as long as the type does, and the cited acts are amended on their own schedules, so keep the approval documents for each system and version and name someone to watch the acts. Daptic tracks regulatory changes like these across jurisdictions, flags the ones that affect your products and works out which requirements apply to a given vehicle in a given market.

Where do manufacturers and suppliers get GSR2 wrong?

 

  • Old approvals: an approval granted before July 6, 2022, was not cancelled, but it doesn’t cover requirements that GSR2 changed or added.[1] Each new row still applies to the older type from its registration date.
  • One model, several rows: versions of one model can fall into different categories with different dates. Tyre pressure monitoring had long been required on M1 cars up to 3,500 kg, but it became mandatory on all new N1 vans only on July 7, 2024.[1]
  • Hydraulic power steering: cars and vans with hydraulic power-assisted steering take the code C dates for emergency lane keeping and fit lane departure warning instead.[1]
  • Exemptions that stop short: some buses and trucks are exempt from lane departure warning and emergency braking, including off-road and special-purpose vehicles and those with more than three axles.[1] The exemption covers those two rows only, so blind spot information, collision warning and direct vision still apply.
  • Switch-offs: the driver may switch intelligent speed assistance off, but it comes back on each time the vehicle is started, and emergency braking and lane keeping can be switched off only one at a time.[1]
  • Stock at the cut-off: after a registration date, vehicles built to the old specification can be registered only under the end-of-series rules. The manufacturer applies to each member state with its technical or economic reasons, and the member state decides within three months. Registration is then allowed for 12 months after the approval lapsed, or 18 months for vehicles completed in stages, within quantity limits.[2]

What is still changing in GSR2?

 

On June 5, 2025, the Commission adopted Delegated Regulation (EU) 2025/1122, which took effect on September 1, 2025, and moved the cited acts to newer series of UN Regulations. These include the 02 series of UN Regulation No 152, which adds pedestrians and cyclists to emergency braking for cars and vans.[3] It also added UN Regulations No 167 for direct vision and No 169 for heavy-duty event data recorders, plus No 171 on driver control assistance, which applies only if fitted. Older pedestrian-protection approval methods stay accepted until September 1, 2029, and September 1, 2031.[1, 3]

 

On December 16, 2025, the Commission proposed, in its Automotive Omnibus, that electric N2 vans between 3.5 and 4.25 tonnes no longer need a speed limitation device.[1] It is only a proposal. Parliament’s committee voted on November 4, 2026, and a plenary vote is scheduled for December 14, 2026, so the requirement still applies.

 

By July 7, 2027, the Commission must report on how the systems perform in use, including a specific evaluation of intelligent speed assistance in real driving, and it may propose changes. Further reports follow every five years.[1]

 

From January 7, 2029, direct vision and heavy-duty event data recorders are mandatory on every new bus and truck. New types have needed them since January 7, 2026.[1, 4]

Example: applying GSR2 to one van line

 

Here is an example of applying this article to one vehicle line, built as a composite of cases. A panel van type first approved in 2020 comes in diesel versions at 3.5 tonnes with hydraulic power steering, and in an electric version whose battery takes it to 4.0 tonnes.

 

The diesel versions are N1. To keep registering them after July 7, 2024, they needed intelligent speed assistance, alcohol interlock facilitation, drowsiness warning, the emergency stop signal, reversing detection, an event data recorder, tyre pressure monitoring and emergency braking for vehicles ahead. Because of the hydraulic steering, they fitted lane departure warning instead of emergency lane keeping. It was due by July 7, 2026, along with distraction warning, pedestrian and cyclist braking, the enlarged head impact zone and the forward vision requirement.

 

The electric version is N2, so the bus and truck rows apply. It already needed lane departure warning, heavy-vehicle emergency braking and a speed limitation device, and it added blind spot information, collision warning and heavy-duty tyre pressure monitoring by July 7, 2024, then distraction warning by July 7, 2026. It needs no event data recorder until January 7, 2029, four and a half years after the diesel versions, when it also needs direct vision.

 

Diesel vans built in June 2026 without distraction warning needed an end-of-series derogation in each member state to be registered after July 7, 2026.

Frequently asked questions

Is GSR2 mandatory for all new cars in the EU?

Yes. Since July 7, 2024, every new car registered in the EU has needed the code B systems, such as intelligent speed assistance and emergency braking. Since July 7, 2026, it has also needed the code C systems, such as advanced driver distraction warning.

What are the GSR2 deadlines for trucks and buses?

Blind spot information, pedestrian and cyclist collision warning and tyre pressure monitoring became mandatory on every new truck and bus on July 7, 2024, and distraction warning followed on July 7, 2026. Direct vision and the heavy-duty event data recorder apply to every new truck and bus from January 7, 2029.

Can drivers switch off intelligent speed assistance?

Yes. The driver can switch it off, but it returns to normal operation each time the vehicle is started.

Does a UN Regulation approval count under GSR2?

Yes. Where GSR2 cites a UN Regulation, an approval to that UN Regulation counts as EU type approval.

Can unsold vehicles still be registered after a GSR2 deadline?

Only through an end-of-series derogation from each member state. It allows registration for up to 12 months after the approval lapsed, or 18 months for vehicles completed in stages, within quantity limits.

Does GSR2 apply to trailers?

Partly. Every new O3 and O4 trailer has needed tyre pressure monitoring since July 7, 2024, but the driver assistance systems apply only to motor vehicles.

Notes and sources

 

  1. Regulation (EU) 2019/2144 (GSR2), consolidated text of August 2, 2026, particularly Articles 2, 3, 6, 7, 14(1), 15, 16(1), 18 and 19; Article 4(5) and Annex II; Article 4(1) and recital 35; Annex II, table and notes to the table; Article 5(1) and Annex II, rows C13 and C14; Article 4(2) and Annex I; Annex II, row C13; Annex II, row C3 and note 6; Annex II, rows C2 and C8 and note 4; Annex II, row B2 and note 18; Article 3 (new Article 9(5a) of Regulation (EU) 2019/2144); Annex II, rows B9 and E5.
  2. Regulation (EU) 2018/858, particularly Articles 3, 4(1) and 48; Article 49 and Annex V, Part B.
  3. Commission Delegated Regulation (EU) 2025/1122, particularly recitals 1 and 2; recitals 3 to 6.
  4. Commission Delegated Regulation (EU) 2024/2220, particularly Articles 1 and 7.

 

Additional sources:

 

 

This article reflects Marc Haddad’s independent opinions, not necessarily those of Daptic.

Resources

Related Articles

Request a Demo Today